Search results

Jump to navigation Jump to search

Page title matches

Page text matches

  • Knee Continuation Drill as described by Jim Merrell
    Here's a knee continuation drill for you: 1) Line up at the foul line for a typical one step drill. (one step back from
    1 KB (217 words) - 22:38, 10 July 2019
  • Drill Sheets
    * [[Columbia drill sheets|Columbia]] * [[Motiv drill sheets|Motiv]]
    342 bytes (37 words) - 14:23, 21 January 2017
  • Bowling Drills Illustrated by Verity Crawley
    Below are a few key components you can work on with each drill: '''Foul line drill:''' <br />
    737 bytes (130 words) - 10:21, 7 October 2018
  • Bowling Drills Illustrated By Verity Crawley
    Below are a few key components you can work on with each drill: '''Foul line drill:''' <br />
    737 bytes (130 words) - 09:57, 7 October 2018
  • MoRich extra sheets
    ==Extra Drill Sheets== Drill sheets courtesy of Mo Pinel and [http://www.morichbowling.com MoRichBowling
    835 bytes (106 words) - 22:19, 22 April 2011
  • Free Swing Drill as detailed by Jim Merrell
    *'''Free Swing Drill as detailed by Jim Merrell''' ...Added 6/28/2012 A drill useful for helping a student feel a free arm swing:
    2 KB (350 words) - 12:24, 2 July 2012
  • Reducing Grip Pressure
    '''Quote 1 is by Mo Pinel''' - '''A Drill'''<br /> '''There is a drill''' that says to open your hand at the top of the backswing. <br />The ball
    2 KB (375 words) - 14:18, 5 May 2013
  • Dual Angle Ratio Guide
    # Degree of drill angle + degree of val angle = Total Sums. # The ''drill angle'' helps determine the length of the ''skid phase'' of ball motion.
    9 KB (1,322 words) - 14:44, 14 November 2013
  • Two Stage Bevel
    ...re already using. For this particular example, we'll choose a 15/16 pilot. Drill the pilot hole to normal depth and at your normal pitches. [[Image:Dscn1248 ...t or hardware store. [[Image:Dscn1249.jpg|thumb|5/32-inch vent hole. These drill bits are available at most hardware stores.]]
    6 KB (1,184 words) - 09:23, 20 April 2011
  • Effects of Drilling Finger Holes Deeper
    There are times when it is suggested to drill finger holes deeper to maintain static weight limitations when using certai
    923 bytes (142 words) - 10:42, 22 April 2011
  • Gradient Line Balance Hole
    If we need to increase thumb weight, the easiest way to do this is to drill the finger holes deeper, up to 4.25" deep. Most of the time, finger holes a If we need a more positive side weight, one way to get it is to drill the middle finger hole much deeper than the ring finger hole, up to 4.25" d
    5 KB (960 words) - 14:54, 10 April 2014
  • Turbo Switch Grip Tips
    '''Fix''': Ice! The heat generated from the drill bit will sometimes cause the inner sleeve to swell and lock onto the outer
    1 KB (266 words) - 19:10, 23 December 2011
  • Rico
    ==About Rico Drill== [[Image:Ricodrill.JPG|thumb|right|100px|Example of Rico Drill.]]
    5 KB (828 words) - 20:03, 4 February 2012
  • Sport Bowling Layouts
    We burn tilt and rotation faster, reduce the drill angle to read the pattern early, and increase the VAL angle to smooth out t Why? Because I can control the drill angle easier, especially those with .018 intermediate differential or great
    10 KB (1,702 words) - 16:35, 26 August 2016
  • Coaching
    *[[Free Swing Drill as detailed by Jim Merrell]] ...Added 6/28/2012 *[[Knee Continuation Drill as described by Jim Merrell]] ... Added 7/10/2019
    4 KB (569 words) - 12:46, 19 September 2019
  • Proshop Information
    :[[Drill Sheets|Manufacturer Drill Sheets]] ...simplesymmetrical.jpg|Mo's Simple Symmetrical Layouts]] - Perpetual Motion Drill Sheet by Mo Pinel<br />
    7 KB (926 words) - 06:35, 11 November 2019
  • RotoGrip
    ...de weight, and then marked with a 4 point star. The idea was that you just drill right over the four point star and you would not have to scale the ball on
    3 KB (456 words) - 19:12, 16 July 2007
  • Jayhawk Fitting Tips
    ...an important aspect of making a customer feel confident in your ability to drill his new equipment and possibly gain you a new customer for life!! Here are
    4 KB (673 words) - 18:58, 23 December 2011
  • RG Contour Explanation
    ...t would form a circle on the ball between the equator and the pin. Once we drill the ball, the RG contours change shape and the circles become ellipses.
    4 KB (781 words) - 10:56, 4 May 2011
  • Coverstock
    ...the rubber coverstock had the tendancy to heat up from friction due to the drill bit partially melting the softer rubber shell, emitting a profound odor mos
    6 KB (922 words) - 20:08, 4 February 2012

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)

Retrieved from "http://wiki.bowlingchat.net/wiki/index.php?title=Special:Search"